Model year record
2004 Porsche 911 GT3 recalls & problems
The 2004 Porsche 911 GT3 has no safety recalls on file with NHTSA, and 27 owner complaints. The most-reported problem area is engine (22 complaints).
Safety recalls
No safety recalls have been filed for the 2004 Porsche 911 GT3.
Recall repairs are free at any authorised dealer. A recall listed here may already have been fixed on a particular car: enter its 17-character VIN at nhtsa.gov/recalls to see open recalls.
What owners report
| Problem area | Complaints | Typical mileage* |
|---|---|---|
| Engine | 22 | 30,500 mi |
| Engine and engine coolingCooling system | 4 | 31,500 mi |
| Power train | 3 | 28,010 mi |
| Unknown or other | 2 | — |
| Fuel system, gasoline | 1 | — |
*Median odometer reading when the problem happened, where owners gave one. One complaint can name several problem areas.
Recent owner complaints
- Engine
THE CAR WAS BEING DRIVEN WHEN SUDDENLY THE COOLANT SYSTEM FAILED AND COOLANT SPILLED FROM UNDER THE ENGINE CAUSING MY CAR TO SKID OUT OF CONTROL. THE COOLANT ALSO POSED A HAZARD TO OTHER CARS ON THE ROAD DUE TO THE EXTREMELY SLIPPERY NATURE OF THE LIQUID. THE CAR HAD TO BE TOWED TO AN INDEPENDENT MECHANIC. THE COOLANT LINES HAD TO BE REPLACED AND WELDED RATHER THAN THE EPOXY GLUE THAT WAS USED IN THE ORIGINAL COOLANT FITTINGS. PORSCHE DEALERSHIPS WOULD ONLY USE EPOXY TO SEAL THE FITTINGS WHICH WOULD ONLY EVENTUALLY LEAD TO ANOTHER FAILURE.
- Power train
I WAS DRIVING AROUND A CORNER ABOUT 40 MPH WHEN THE CAR SUDDENLY SPUN AROUND. I THEN SAW STEAM COMING FROM THE ENGINE. UPON FURTHER INSPECTION THERE WAS COOLANT ON THE GROUND. ONE OF THE COOLANT FITTINGS HAD COME COMPLETELY LOOSE, AND ALL THE COOLANT HAD LEAKED OUT. THE ONLY REAL FIX IS TO WELD ALL THE COOLANT FITTINGS. THERE ARE 9 OF THEM AND THE ENGINE HAS TO BE REMOVED TO DO THE WELDING. IT COST ME $2500 TO FIX THIS DEFECT. THIS IS A SAFETY ISSUE AS I WAS LUCKY I DID NOT HIT ANY ONE OR ANY THING. JUST PURE LUCK. WHEN YOU DUMP LARGE QUANTITIES OF SLIPPERY COOLANT ON TO THE REAR TIRES IT IS JUST A MATTER OF TIME BEFORE SOMEONE IS KILLED. THIS PROBLEM IS SO PREVALENT THAT MOST RACE TRACKS…
- Unknown or other
ON VERY HOT DAY, OVER 100 DEGREES F, AFTER HAVING JUST EXITED A FREEWAY ONTO A CITY STREET, WHILE ACCELERATING FROM RED LIGHT, A GLUED-IN WATER COOLANT PIPE/TUBE POPPED OUT FROM ITS CAST HOUSING, CAUSING CATASTROPHIC LOSS OF ALL COOLING FLUIDS WHICH SPILLED ONTO THE ROADWAY, IMMEDIATE INCREASE IN ENGINE TEMPERATURE FROM 185 TO OVER 260 DEGREES F, AND LOSS OF POWER. CAR NEEDED TO BE TOWED TO REPAIR SHOP.
- Engine
A COOLANT LINE FITTING THAT IS EPOXIED INTO THE BLOCK BECAME SUDDENLY AND COMPLETELY DISCONNECTED. THE COOLANT ALL FLOWED OUT OF THE LEAK NEARLY INSTANTLY. THE POOL OF COOLANT CREATED A HAZARD FOR FOLLOWING CARS AND THE MOTOR NEEDED TO BE SHUT DOWN IMMEDIATELY AND THE CAR TOWED TO A SERVICE FACILITY. *JS
- Engine
WENT TO STREETS OF WILLOW DRIVING EVENT. DURING 3RD RUN SESSION I NOTICED STEAM COMING FROM BEHIND AS I WAS TAKING A 180 DEGREE TURN. I IMMEDIATELY STOPPED THE CAR WHEN IT WAS SAFE TO DO SO AND SHUT THE ENGINE OFF. STEAM KEPT BILLOWING AND THE CAR SEEMS TO HAVE LOST ALL IT'S COOLANT IN A FEW SECONDS. 5(!) CARS BEHIND ME ALL SPUN IN THE 180 DEGREE TURN BECAUSE OF THIS FAILURE. FORTUNATELY NONE OF THEM CRASHED. AFTER EXAMINATION IT TURNS OUT ONE OF THE COOLANT FITTINGS THAT PORSCHE GLUED INTO THE MOTOR BLOCK WITH EPOXY HAD POPPED OUT. THIS APPEARS TO BE A VERY COMMON PROBLEM WITH ALL OF THESE GT ENGINES. NOT ONLY IS THIS DANGEROUS (EVERY GT2/3 ON THE ROAD IS A TICKING TIME BOMB, STREET OR…
- Power train
I WAS DRIVING AT MILLER MOTORSPORTS IN TOOELE UTAH IN DRIVERS EDUCATION EVENT WHEN MY ENGINE TEMPERATURE GAUGE STARTED TO INCREASE FROM 180 DEGREES UP PAST 200 DEGREES. AS THE TEMPERATURE GAUGE WENT TO 250 DEGREES, A COOLANT FAILURE LIGHT CAME ON. I PULLED OFF THE TRACK AND SHUT DOWN THE CAR WITHIN 2 MINUTES OF THE FAILURE LIGHT AND I HAD TO BE TOWED OFF THE MILLER MOTORSPORTS TRACK. I HAD LOST ALL OF MY COOLANT FROM THE CAR. THE NEXT MORNING (SUNDAY) I TOOK A RENTAL CAR BACK TO MILLER MOTORSPORTS ALONG WITH 9 GALLONS OF DISTILLED WATER. I POURED 2 GALLONS OF DISTILLED WATER INTO THE CAR, AND THEN STARTED IT. ABOUT SEVEN MINUTES LATER, WATER STARTED SPURTING FROM AN ALUMINUM COOLANT LINE…
- Engine
THE EPOXY HOLDING AN ALUMINUM ELBOW THAT CONNECTS A COOLANT HOSE TO THE WATER PUMP (I BELIEVE) LET GO, THE ELBOW WORKED ITS WAY LOOSE FROM THE PUMP AND EMPTIED THE COOLANT FROM THE SYSTEM OUT ONTO THE ROAD SURFACE. I BECAME AWARE OF THE PROBLEM WHEN I NOTICED THAT THE ENGINE TEMPERATURE NEEDLE HAD PEGGED AT THE HIGH END OF THE GAUGE RANGE, AFTER WHICH THE ENGINE TEMPERATURE WARNING LIGHT CAME ON. PRIOR THERETO, THE ENGINE TEMPERATURE GAUGE HAD BEEN READING AT NORMAL LEVELS AND RESPONDING NORMALLY. I WAS ABLE TO STOP WITHOUT AN ACCIDENT, BUT I NOTICED AFTER STOPPING THAT THE RIGHT REAR TIRE AND WHEEL WELL WERE WET AND SLIPPERY WITH COOLANT.
- Engine
WHILE DRIVING AT A DRIVERS EDUCATION EVENT AT WATKINS GLEN RACE TRACK, A COOLANT FITTING CAME APART AND OUT OF ITS HOUSING RELEASING ABOUT 3-4 GALLONS OF COOLANT ONTO THE TRACK. LUCKILY NO ACCIDENT OCCURRED. SINCE THE CAR WAS STILL UNDER WARRANTY PORSCHE AGREED TO COVER THE FAILURE UNDER GOOD WILL AND A NEW HOUSING (SAME DESIGN) WAS INSTALLED BY THE LOCAL PORSCHE DEALER. HOWEVER, IN OCTOBER, 2011 WHILE DRIVING AT ANOTHER DRIVERS EDUCATION EVENT, THE SAME FITTING FAILED. THIS TIME 3 CARS FOLLOWING ME SLID OFF THE TRACK DUE TO THE COOLANT WITH ONE CRASHING INTO ANOTHER. ONE CAR WAS TOTALED AND THE OTHER SERIOUSLY DAMAGED. *TR
Owner complaints are submitted to NHTSA by the public and are not verified. Shown as filed (NHTSA removes personal details); long reports are shortened.
NHTSA defect investigations
- Rapid coolant lossClosed
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data…