Model year record
The 2018 Can-Am Spyder F3 has 2 safety recalls and 14 owner complaints on file with NHTSA. The most-reported problem area is power train (6 complaints).
Recall repairs are free at any authorised dealer. A recall listed here may already have been fixed on a particular car: enter its 17-character VIN at nhtsa.gov/recalls to see open recalls.
| Problem area | Complaints | Typical mileage* |
|---|---|---|
| Power trainDriveline › Chain/belt | 6 | — |
| Service brakes | 3 | — |
| Vehicle speed control | 2 | — |
| Unknown or other | 2 | — |
| Engine | 2 | — |
| Fuel/propulsion system | 2 | — |
| Parking brake | 1 | — |
*Median odometer reading when the problem happened, where owners gave one. One complaint can name several problem areas.
BRP has a recall for the output shaft for the 2018 Can Am Spyder F3T. Just after receiving the recall letter the output shaft on my Spyder went out. My bike does have more than the 37,000 miles on it. This is a known defect with this Bike. It is not right that BRP knows this part is defective and has a milage limit on it. This bike is my daily driver for work. I have contacted BRP and have been told as my bike has more miles that i am just up a creek without a paddle as I still owe more than $11,000. on this bike. I have asked for a call back and have not received any. I think this is wrong of them to put a milage cap on this part as it is designed to last the bike its lifetime. I have even…
The affected part is the engine output shaft, which is part of the vehicleâs powertrain and propulsion system. BRP issued Recall 24V-728 for this defect, stating that the shaft can break and cause a sudden loss of propulsion, creating a safety hazard. I received the recall notice in April 2025 and have been unable to safely operate the vehicle since then. I contacted every authorized Can-Am dealer within 150 miles, but all confirmed they could not perform the recall repair because replacement parts were unavailable. The first available dealer, Team Mancuso Powersports Southwest, accepted the vehicle on September 23, 2025, and has now had it for over three weeks with no estimated repair…
The contact owns a 2018 Can-Am Spyder F3. The contact received notification of NHTSA Campaign Number: 24V728000 (POWER TRAIN); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
While riding at approximately 65 miles per hour, the vehicle started to get slower and slower until it eventually came to a stop. The vehicle had 15,451 miles on the odometer at the time of the failure and had to be towed to a dealership for inspection / repair. The dealer advised that the shaft that the sprocket rides on had excessive play and that the intermediate shaft failed / snapped.
While driving on a straight stretch of highway at posted highway speeds of 75mph, no additional acceleration, torque, turning, or high rpms, my bike experienced a sudden jolt and immediate loss of propulsion. I was able to pull to the side of the highway to find my front left drive shaft had completely sheared off, the front sproket (currently under recall, which has not yet been replaced according to my dealer's service records) thankfully was caught by the frame underneath or it could have flown out into traffic and hit the other biker behind me or other traffic, or causing me to crash. My drive belt remained fully in tact but was dislodged and dragging, another risk factor for crash.…
The contact owns a 2018 CAN-AM Spyder F3. The contact stated that the parking brake was inoperable. The parking brake had seized. The brake warning light was illuminated. The vehicle was taken to the local dealer where it was diagnosed that there was a defective parking brake motor and a TSB regarding the failure had expired. The manufacturer was contacted and referred the contact to the dealer for assistance. The failure mileage was approximately 17,500.
The contact owns a 2018 Can-Am Spyder F3. The contact received notification of NHTSA Campaign Number: 22V352000 (Power Train) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. Parts distribution disconnect.
Shifting / stalling problems: 2018 F3L SE6 **Problem has occurred using each of my 2 Spyder keys Problem definition: At times, bike stalls while driving...begins shaking and remains in last gear prior to the stall. Gear shown in Display does not change from gear it was last in when bike stalled out. Orange exclamation point ! (Vehicle Malfunction) appears on lower left corner of Display and the last gear the bike was in prior to stalling still appears on Display. The gray banner, Transmission Fault also flashed quickly on Display for 2 of the 4 total fault occurrences. This happened when I was traveling in higher gears, approx. RPM at 3900-4200, as in 3rd, 4th, 5th or 6th gear. It stalls…
Owner complaints are submitted to NHTSA by the public and are not verified. Shown as filed (NHTSA removes personal details); long reports are shortened.