Model year record
The 2018 Can-Am Spyder RT has 2 safety recalls and 12 owner complaints on file with NHTSA. The most-reported problem area is power train (6 complaints).
Recall repairs are free at any authorised dealer. A recall listed here may already have been fixed on a particular car: enter its 17-character VIN at nhtsa.gov/recalls to see open recalls.
| Problem area | Complaints | Typical mileage* |
|---|---|---|
| Power train | 6 | — |
| Steering | 2 | — |
| Service brakes | 2 | — |
| Fuel/propulsion system | 2 | — |
| Engine | 2 | — |
| Seats | 1 | — |
*Median odometer reading when the problem happened, where owners gave one. One complaint can name several problem areas.
The contact owns a 2018 Can-Am Spyder RT. The contact stated that while driving at 35 MPH and attempting to upshift into the next gear, the shifter seized and failed to operate as designed. The contact pulled over, and the vehicle was towed to a local dealer, where the vehicle was diagnosed, and the contact was informed that the left shifting switch on the handlebar was faulty and needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 2,200.
My wife RODE our 2018 Can Am Spyder 70 miles to have recall 24V728 completed on 4/23/25. Today is 6/24/25 and we still do not have vehicle back. Dealership pulled engine replaced output shaft put it back together and it will now not shift correctly. Dealership has been trying to figure out the problem and in contact with BRP. At first it was something about it not accepting updated programming, then it was something about an oil pressure sensor creating the issue, and now they say it is the HCM which I believe is hydraulic control module in the transmission. On May 7th in an email from BRP Customer Service this statement below was made by the customer service representative. "I have spoken…
After receiving the safety recall notice from the manufacturer, BRP, in January 2025, I attempted to have the safety recall completed at a dealership in the Pittsburgh PA area. I was initially told by the MOSITES Dealership that they were not able to complete the safety recall because of the time it takes to perform the recall, which ties up their service lifts and mechanic's time. I contacted BRP, who contacted MOSITES WEST in Pittsburgh, PA, and they made a service appointment to complete the safety recall on April 3rd. I dropped the bike off for service on April 3rd. Weeks later, I was told by Gabe in the MOSITES Service Dept. they were waiting for parts and had not started the repair. I…
The contact owns a 2018 Can-Am Spyder RT. The contact received notification of NHTSA Campaign Number: 24V728000 (POWER TRAIN). The vehicle was taken to a local dealer; however, the recall repair was not completed. The manufacturer was made aware of the issue; however, the manufacturer declined to repair the vehicle. The contact was informed that the mileage requirement had been exceeded as stated in the recall remedy. The contact had not experienced a failure. Parts distribution disconnect.
Referance Recall Number 24V728. On 22 Jan 2025 manufacturer BRP indicates vehicle does NOT require defective output shaft replacement for vehicles with mileage over 37282. My vehicle has a little over 40,000 miles. In Part 573 Safety Recall 24V-728 (22 Jan 2025) "Vehicle 2" states "All the My2018 population was assembled with the new flexation method and are included". Taking this strategy, BRP is failing to repair a vehicle included as part of the at risk population of vehicles. A safety recall should have no mileage cap. Safety recalls involve USE, VALUE, and SAFETY, not longevity/mileage.
The contact owns a 2018 Can-Am Spyder RT. The contact received notification of NHTSA Campaign Number: 24V728000 (Power Train); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue and opened a case. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2018 Can-Am Spyder RT. The contact received notification of NHTSA Campaign Number: 22V352000 (Power Train) however, the part to do the recall repair was not yet available. The dealer was made aware of the issue. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact had not experienced a failure. VIN tool confirms parts not available.
While driving the vehicle a clunking sound was heard and at the same time I experienced a loss of propulsion. The vehicle is currently in the process of being repaired as it was determined that the front drive sprocket main drive shaft had sheared. Fortunately I was able to pull off the highway at an intersection onto a much less congested street. There were not warning lights or indications that forewarned me of this event. The vehicle was towed as it was unable to proceed under its own power to the residence of the owner. After further evaluation the vehicle was taken to a dealership for diagnosis and repair. The VIN provided has no displayable records on Carfax.
Owner complaints are submitted to NHTSA by the public and are not verified. Shown as filed (NHTSA removes personal details); long reports are shortened.